<dl id="pll7d"></dl>

      <nobr id="pll7d"><listing id="pll7d"></listing></nobr> <address id="pll7d"></address><sub id="pll7d"></sub>
      <big id="pll7d"></big>

      <big id="pll7d"></big>

      EN | 中文

      Selection of raw materials for interior and exterior latex paint

      Publication time:2018.08.17 10:30

      Times of browsing:

      Selection of raw materials for interior and exterior latex paint

       

      Yang wenyuan (taizhou silian chemical co., LTD., 225312)

       

      Abstract: the selection of raw materials for interior and exterior latex paint is discussed in order to produce high cost effective latex paint.

       

      Keywords: interior wall latex paint; Exterior wall latex paint; The raw materials

       

      Article no. : 1009-1696 (2012) 04-0044-03

       

      Practical technology

       

      0 the introduction

       

      In the past ten years, it should be said that China's economy has been developing rapidly

       

      Ten years, of course, is the architectural paint rapid development stage. According to the

       

      Statistics show that the annual output of China's construction coating was 3,518,000 tons in 2010

       

      Annual production was six times in 2001. Average annual paint usage per person is a measure

       

      The bellwether of national economy and people's living standard. With developed countries

       

      Than, the use amount of building coating per capita still is very low in our country. Statistically, I

       

      The per capita construction paint consumption in China is 2.6kg /a, and the per capita construction paint in cities and towns

       

      The material usage amount is 5.5 kg/a, while that of building coating per capita in developed countries such as Europe and America

       

      Material usage: over 25 kg/a. With China's future urbanization process

       

      The acceleration of urban population growth, coupled with urban and rural for housing

       

      Demand improvement, decoration demand will further rise in the foreseeable

       

      In the future, the demand for interior and exterior wall coatings will still be on the rise.

       

      There is a lot of room for improvement of architectural paint usage in China.

       

      As the demand for interior and exterior emulsioni paint continues to rise in recent years

       

      A large number of medium - sized paint production enterprises. Although the exterior wall latex

       

      Paint production technology gradually mature, but with the scale of large enterprises

       

      Production, small businesses are increasingly struggling, many even

       

      Without their own professional technical staff, the paint product formula is either one

       

      Some high quality raw materials piled up, or some inferior raw materials pool

       

      Set, coating performance stability and overall profits are also discounted.

       

      This paper attempts to combine the author's experience in the process of the shallow

       

      The formulation, raw material selection and production process control of exterior and interior latex paint are discussed

       

      Uniform elements.

       

      Basic formula of inner and outer wall emulsion paint

       

      With GB/T 9756-2009 "synthetic resin emulsion interior wall coating" and

       

      GB/T 9755-2001 "synthetic resin emulsion exterior wall paint" as an example

       

      Formula of internal and external emulsioni paint (see table 1). Additional, inside wall emulsioni paint return

       

      Mandatory standard GB 18582-2008 must be met.

       

      Table 1. Basic formula of exterior and interior latex paint

       

      Table 1 The formulation of interior/exterior latex paint

       

      Interior wall emulsion paint base formula (white) exterior wall emulsion paint base formula (white)

       

      Serial number material name quantity /‰

       

      1 water 250 1 water 120

       

      2 wetting agent PE100 1 2 wetting agent PE100 1

       

      3 dispersant SN5040 6 3 dispersant SN5040 6

       

      4 defoamer NXZ 1 4 defoamer NXZ 1

       

      5 propylene glycol 10 5 propylene glycol 10

       

      6 preservative LXE 2 6 preservative LXE 1.5

       

      7 anatase titanium 60 7 rutile titanium 120~150

       

      84,000 megasolinite 80~100 8 heavy calcium 150~250

       

      9 800 mesh heavy calcium 150~250 9 barium sulfate 50

       

      10 barium sulfate 60 10 wollastonite 40

       

      11 talc powder 40 11 styrene emulsion 240~260

       

      12 styrene-acrylic emulsion 120 12 film forming assistant

       

      TEXANOL

       

      5 to 7

       

      13 film forming assistant

       

      TEXANOL

       

      5~7 13 defoaming agent NXZ 1.5~2

       

      14 defoaming agent NXZ 1.5~2 14 rheology auxiliaries appropriate

       

      15 suitable amount of the rheological agent 15 suitable amount of cellulose thickening agent

       

      16 cellulose thickener appropriate amount of 16 alkali swelling thickener appropriate

       

      17 moderate amount of alkali swelling thickener 17 moderate amount of water

       

      18 a moderate amount of water

       

      PH regulator micro amount

       

      No.4 45

       

      2. Selection of raw materials for emulsion paint

       

      2.1 the emulsion

       

      Emulsion is the most important film forming material in the inner and outer wall emulsion paint.

       

      For internal wall emulsion paint, generally use vinegar emulsion, vinegar tertiary emulsion, benzene

       

      Acrylic emulsion; For exterior wall latex paint, pure propyl emulsion, silicon-propyl emulsion,

       

      Styrene-acrylic emulsion. At present in China, most of the interior and exterior latex paint is benzene

       

      Acrylic emulsion, because of its cost - effective acceptance. To reach the inner wall latex

       

      Performance requirements of lacquer GB/T 9756 -- 2009, in basic formula design,

       

      The most important is the number of times of washing, the emulsion in the formula

       

      Generally 10.5%~12.5%.

       

      2.2 selection of preservatives and fungicides

       

      Whether preservative or fungicide, the variety on the market

       

      Are very complex, the principles of selection are generally efficient, low toxicity, compatibility,

       

      Stable, durable and cost-effective. Use of formaldehyde is becoming increasingly popular

       

      Type of preservative, through its slow release, to achieve a certain degree of germicidal efficacy,

       

      It not only has the advantages of formaldehyde, but also avoids the disadvantages of formaldehyde. general

       

      In the formula, the amount of preservative is 0.1%~0.3%, the use of anti - mildew agent

       

      Content is 0.3% ~ 0.6%. For products that require special mildew resistance, choose

       

      It is better to use two or more fungicides. Fungicides are mainly used

       

      Prevent the wet areas where rain is abundant from producing mildew on the walls and dry in the north

       

      Area production USES emulsioni paint, most enterprises do not add anti - mildew agent.

       

      2.3 selection of wetting dispersant

       

      The wetting, dispersing, and stabilizing of pigments is often closely linked,

       

      Wetting is the process of particle replacement on pigment surface. Disperse is the pigment in

       

      The process of separation under the action of external forces; Stability is the final dispersal

       

      The pigment granules no longer condense twice. The common wetting agent for latex paint is

       

      Cognis PE100; The commonly used dispersants are polyacrylate and polyacrylate

       

      Polyphosphate. In practice, 0.2% polyphosphate and

       

      A mixture of 0.2% to 0.4% polyacrylate. Storage stability of coatings,

       

      Washing resistance is a key index to evaluate dispersant.

       

      2.4 selection of antifoaming agent

       

      Antifoaming agents can be divided into antifoaming agents and defoaming agents. Antifoaming agent has been on

       

      The foaming agent is on the coating surface

       

      The surface plays a role in destroying the bubbles that have formed. In the production of latex paint

       

      In control, antifoaming agents are usually added twice, at the pulping stage and in paint making

       

      Add 1/2 to each stage. Or 2/3 in the pulping stage and 2/3 in the paint stage

       

      In the third. At the stage of pulping, it is best to add a defoaming agent with strong anti-foam effect.

       

      In the paint stage it is best to add the foam breaking ability strong anti - foam agent.

       

      2.5 selection of film forming auxiliaries

       

      The emulsion itself is thermoplastic, so in order to guarantee the film performance,

       

      You don't want it to be too soft, and you want it to be as hot as possible.

       

      Corresponding production of emulsion paint the lowest film temperature is higher, so low temperature

       

      Construction and film formation become a problem, which is through the addition of film auxiliary

       

      To balance.

       

      The amount of film forming AIDS generally depends on the amount of emulsion, but

       

      The vitrification temperature of emulsion also affects the amount of film additives

       

      Big. In addition, such as propylene glycol, ethylene glycol such as antifreeze agent is also certain

       

      And the amount of them to the amount of the film forming AIDS

       

      It has an impact. Furthermore, with the increase of PVC (pigment volume concentration),

       

      That is, the amount of emulsion reduced, the film is more difficult, because with the face filling

       

      The adhesion of the material to the film forming agent greatly reduces the efficiency of the film forming agent.

       

      Most of the production of film additives in the paint phase of emulsion Tim

       

      After adding, such production if the operation is not good, film auxiliary

       

      So that the emulsion quickly polymerized into small particles and coarse, so must be stirred at low speed

       

      Mix slowly in the mix, so that the film agent to play the largest role. There are also

       

      It is added before the painting stage, although it is safer to do so

       

      Hydrophobic film forming AIDS will be wetted by emulsifying, and face filler in advance

       

      Adhesion, the actual effectiveness of film - forming AIDS will be greatly reduced.

       

      The dosage of film forming assistant should be based on the emulsion, adding process, formula,

       

      The different of season, area will be treated flexibly, its regular dosage is emulsion use

       

      0.05 times the amount.

       

      2.6 selection of thickeners

       

      Latex paint is water as the dispersing medium of the paint, and water viscosity

       

      Very low, can not meet the construction requirements, need thickening agent to adjust the flow

       

      Degeneration. Commonly used thickeners are cellulose, non - associative alkali swelling

       

      Type ii and associative alkali swelling type thickeners, their properties are shown in table 2.

       

      Table 2 properties of various thickeners

       

      Table 2 The characteristics of various thickeners

       

      Comparison of cellulose non-associative alkali swelling type association alkali swelling type

       

      The thickening efficiency is higher and higher

       

      PH sensitivity is generally very high

       

      Poor splash resistance is better

       

      Poor leveling is generally good

       

      Flow resistance is better, better and better

       

      The optical retention is generally good

       

      Better water resistance, better and better

       

      Good alkali resistance is general

       

      The prices are higher, moderate and cheaper

       

      Yang wenyuan: the choice of raw material of latex paint for inner and outer walls

       

      Shanghai paint volume 50

       

      It can be seen from table 2 that various thickeners have different advantages and disadvantages in milk

       

      In the paint system, if only one thickening agent is used, the storage stability,

       

      Construction effect and other aspects are difficult to achieve the expected performance, most of them are adopted

       

      Two or more thickeners are used to achieve the desired effect.

       

      2.7 choice of fillers

       

      Take white latex paint as an example, rutile titanium dioxide is the best

       

      White pigment. In our country most manufacturer, interior wall emulsioni paint makes more

       

      Use anatase titanium; use rutile titanium; In the developed countries

       

      The interior and exterior walls are basically rutile - type titanium white.

       

      Commonly used fillers are calcium carbonate, talc powder, sericite powder, gao ling

       

      Soil, silica fume, lithopone, quartz powder, ultrafine aluminum silicate, sulfuric acid

       

      Barium, etc.

       

      Both heavy and light calcium belong to calcium carbonate, of which heavy calcium is the natural mineral

       

      Stone is crushed and light calcium is a synthetic product. Among the many fillers, weight

       

      Calcium should be said is in emulsioni paint usage amount is the biggest, most stable, cheapest

       

      Packing; Although light calcium also has a little dry covering power, suspension is also good,

       

      But easy to start white frost, stability is poorer.

       

      Many interior wall latex paint formulations also use a little talcum powder, though

       

      It is easy to powder, but can improve the construction and leveling of emulsion paint.

       

      Sericite powder belongs to layered silicate, is scale crystal, acid resistant

       

      Good alkali resistance and chemical stability. It can be used in exterior and interior latex paint

       

      Appropriate use, on the one hand can greatly improve the weather resistance of paint film, prevent

       

      Water vapor penetration, on the other hand to prevent powder and paint cracking.

       

      Another important filler is kaolin, which is easily dispersed in water, white

       

      High degree, strong dry covering, thixotropic, paint stability

       

      And in good shape. Through experimental study, we found that the ultrafine 4 000 order

       

      Kaolin and titanium dioxide can be used to improve the covering power of the coating

       

      Comprehensive performance. In white latex paint, silica fume has a bright color

       

      Adjust, can enhance the hardness of paint film, but also improve the durability and resistance of the film

       

      Grinding.

       

      According to the characteristics of the different fillers described above, the inner wall latex paint in general

       

      Products with high whiteness such as heavy calcium, light calcium, talc powder and kaolinite;

       

      Sericite, barium sulfate, wollastonite powder,

       

      Calcined kaolin, etc. Should choose flexibly according to price, demand.

       

      3 conclusion

       

      Although at present the production technology of emulsioni paint is increasingly mature with the technology

       

      The increasingly progressive innovation of art is still developing, while our country until the 20th century

       

      In the early 1990s, with the entry of multinational companies into China brought new

       

      Material, new technology, just begin rapid development. Improve cost performance and increase

       

      Function, low cost, low VOC (volatile organic compounds), low gas

       

      Taste, environment friendly type emulsioni paint will become the mainstream.

       

      To obtain high cost performance emulsion paint required to fine the relevant raw materials

       

      For in-depth comparative research and selection, not raw material piling, no

       

      To obtain good market returns, we must optimize the formulation.

       

      The Selection of Raw Materials for Interior/Exterior Latex Paint

       

      Yang Wenyuan (Taizhou Quad Chemical Co., Ltd., Jiangsu Taizhou, 225312, China)

       

      Abstract: The selection of raw materials for interior/exterior latex paint were brief discussed in order to prepare The

       

      Latex paint with high price performance ratio.

       

      Key Words: interior latex paint; Exterior latex paint; Raw material

       

      Akzo Nobel powder paint released 2012 Interpon F furniture color trend

       

      Recently, akzo Nobel powder paint released the latest Interpon F 2012 color trend designed specifically for the furniture industry.

       

      The latest Interpon F color trend is at the forefront of today's color trends. This series product has 15 kinds of indoor furniture color and 15 kinds of outdoor furniture color

       

      Colors are available.

       

      The latest popular collection is refreshingly based on akzo Nobel's "color trend" series, showing the latest in the furniture market

       

      Color and surface effect trends. Designers can not only have excellent performance and excellent protection of Interpon F powder coating into their own products, at the same time

       

      It also ensures that its design is in line with the latest color trends.

       

      Based on the color trend, akzo Nobel also released the Interpon F color and gloss standard color card, which will help designers better understand

       

      Interpon F's choice of different colors and sheen.

       

      Interpon F furniture powder coating follows the fashion trend, durable and provides first-class protective effect. It can fully meet the durability of the furniture industry and beauty

       

      成a人影片免费观看日本,综合AV第一页,亚洲一本之道高清乱码